by John Deere dealers direct from the John Deere. Distribution Engine (14PZ and 14SZ) A John Deere ILLUSTRUCTION™ Manual. John deere 14sz manual pdf. Free Download 19 51 11 IRP MJ SYSTEM. CONTROL BA5FCB40 exe 07 04 C Windows. John Deere Model 14SZ Walk Behind Mower Parts – The serial number is located John Deere Operators Manual – OMM – See product detail for serial.

Author: JoJozilkree Mek
Country: Kosovo
Language: English (Spanish)
Genre: Art
Published (Last): 23 July 2011
Pages: 117
PDF File Size: 12.6 Mb
ePub File Size: 16.83 Mb
ISBN: 543-8-11615-166-7
Downloads: 65380
Price: Free* [*Free Regsitration Required]
Uploader: Nera

Maintenance, repair, or replacement of the emission control devices and systems on this engine, which are being done at the customers expense, may be performed by any nonroad engine repair establishment or individual. Carburetor is calibrated by the engine manufacturer and should not require any adjustments. If engine is operated at altitudes above m 6, ft.

Engine exhaust fumes can cause sickness or death:. Use oil viscosity based on the expected air temperature range during the period between oil changes. Before you check or add oil, STOP engine. Change oil after first 5 hours of operation.

Remove dipstick and wipe it with a clean cloth. Two different methods can be used for changing the engine oil. Both options are acceptable service procedures based on customer preference.

Insert plastic drain tube B dere inside filler tube opening. Fuel is highly flammable. Prevent fuel from contacting hot surfaces: DO NOT drain fuel tank. Run engine until fuel tank is very low or empty before turning mower on side to change oil. Allow engine oil to 14ss from the dipstick filler tube location into the drain pan.

After oil has drained, return mower to an upright position. Remove plastic drain tube. Clean area around filler tube.

Add oil to FULL mark if necessary. Be careful of sharp manusl on mower blades. Wear gloves when working under deck. Raise cutting height adjustment levers A to the highest cutting position. See Adjusting Cutting Height in the Operating section.

Elevate entire mower an additional mm – mm in. Return cutting height adjustment levers to a desirable cutting height. Before you work on engine:. Dirt and debris can enter the engine through a damaged filter element. Before you remove plug:.

John Deere Operators Manual for a 14pz and 14sz Walk-behind Mower OMM95319

Carefully wire brush carbon from plug. Do not clean it with abrasives in a machine. Wear eye protection to guard against flying debris. Keep fins clean or engine may overheat.


Before you remove shield:. Remove clippings from belt area and top of the transmission. Before removing belt shield:. On model JS61 only, the anti-rotation bracket must be removed prior to pushing the drive sheave forward to remove the drive belt.

Wear protective eyewear when removing belt from drive sheave. Tension spring may come loose.

John Deere Ag – New Equipment: Technical Publications – Publications Search

Push drive sheave G forward to relieve spring tension on belt. Tension spring H may come loose when belt is removed. Push drive sheave J forward and install belt to sheave. Install anti-rotation bracket and secure with cap screw. Help prevent bodily injury. Wear protective eye wear when removing belt from drive sheave. Transmission cable adjustment can be performed without removing belt and pulley.

The belt and pulley have been removed for clarity of pictures. Push drive sheave E forward to relieve spring tension on belt and remove drive belt F. Measure the clutch spring length H in the relaxed position. Engage the transmission bail at handle bar and measure the spring length in the extended position I. The spring extension length the difference between A and B measurements must be 10 mm 0. To adjust spring extension, use an 8 mm wrench, loosen do not remove the cable mount bracket capscrews J.

For transmission clutch to operate properly, there must be a certain amount of spring pressure engaging the cones or the transmission will slip and NOT drive the wheels. Slide bracket K the required distance to obtain the 10 mm 0. Repeat steps 6 and 7 to verify the 10 mm 0. Install cover and secure with two bolts and two bolts and nuts.

Make sure shield is installed with cover. Start engine and verify the transmission is operating properly. Make sure the transmission immediately disengages when the bail is released. If transmission does not disengage when bail is released, reduce spring extension length, and verify transmission is operating properly.

Lubricate drive shaft hub bushings every 25 hours or once a year. Remove control cable C from belt shield notch D. Tilt mower slightly to one side. Lubricate driveshaft hub bushing E with a few drops of light weight motor oil.


John Deere 14sz Manual – video dailymotion

Repeat procedure for other side. Slide control cables C into belt shield notch D. Lubricate each mower axle every 25 hours or once a year. Tip mower to one side to elevate mower wheels slightly off the ground.

seere Use a uohn block to keep side of mower in a raised position. To help prevent air cleaner damage and hard starting:. Sharpened edges on blade tips must face upward when installing blade. See Sharpening Blade in this section. To avoid injury, wear gloves and goggles when sharpening, balancing or installing blade. Balance blade after you sharpen it. An unbalanced blade may cause excessive vibration.

Sharpen blade with grinder, hand file or electric blade sharpener. Keep original bevel A when you grind. Blade should have 0. Put it on a nail in vise or on a wall.

Heavy end of blade will drop. Grind bevel of heavy end. Do not change bevel. Dirt and water in fuel are major causes of engine performance problems.

Prevent dirt and debris from entering the fuel tank when filling. Fill the tank at the end of each day’s operation to help keep condensation out of the fuel tank.

If engine is hot let it cool several minutes before you add fuel. Fill tank with fresh fuel only to bottom of filler neck. Check two vents A under metal ring of fuel cap and vent in top, center of cap. Clean cap and vents in nonflammable solvent. Allow cap to dry. To help prevent air cleaner damage and hard starting: Fuel tank capacity is 1. Service Engine Warranty Maintenance Statement Maintenance, repair, or replacement of the emission control devices and systems on this engine, which are being done at the customers expense, may be performed by any nonroad engine repair establishment or individual.

Engine exhaust fumes can cause sickness or death: Before you work on engine: Before you remove plug: Before you remove shield: Before removing belt shield: About Our Site Privacy Legal.